Technology of laying gypsum tiles along with your own hands


Gypsum tiles must be laid properly, as not only the aesthetic look of decorative facing, but also the service life of the

substance will be dependent on the technology of work. The product is universal, and it may be attached to concrete, plaster,

brick or gypsum board sheets, provided that the surface of the foundation is and has no flaws.

If the flaws of the base are important, it should be thoroughly treated with primer, then a cement mortar is created, which

matches all the cracks. Subsequently the surface ought to be repeatedly primed and dried. Primer treatment is necessary to improve

the bond between the tile and the walls. In this case, its makeup should select a particular, comprising elements that prevent the

appearance of fungus and mold.

In the modern interior of these rooms most often used gypsum tiles, even imitating natural brick or stone. To execute cosmetic

finishing yourself, it’s necessary firstly to choose a strategy of tile positioning and prepare a remedy. It’s very important to

look closely at the opposite side of this material. If its surface has an embossed surface, then the adhesive ought to be placed

having an even trowel, also if it is even, then with a top notch one.

The technologies of this job is as follows:

* A thin layer of adhesive is applied to the pre-prepared wall. It is distributed over the bottom so it is likely to place 4-5

tiles. Decorative cladding may be placed either on plasterboard, and on putty.

* Cover the back side of the tiles with glue.

* Plaster elements are pressed against the wall and their location is adjusted. To align the seams, it’s advised to use spacers.

* Finishing is carried out in rows, each of which should be changed by half of a tile. Facing is carried out to the corners of

the space, and then immediately remove any residual mortar at the joints.

Drying the walls requires no more than a day also takes a constant humidity and temperature within the room. The last stage in the

placing of gypsum tiles is their own decor. To do this, the joints between the elements are full of a unique solution, the shade

of which suits the brick.

Decorative imitation of brickwork on the walls has been completed in the following ways:

* Cutting the darkened surface of the stitches of masonry with a bolt cutter with your hands;

* placing of tiles beneath the brick:

* mimicking the structure and colour of the side surface of one brick;

* Imitating a fragment of brickwork of several bricks.

The perfect method to decorate”beneath the brick” is really the one that allows you to create a functional coating together with

the maximum appearance of its similarity to organic masonry. All three methods to execute this sort of finishing works meet the

requirements, however, the cutting edge of joints using a bolt is more labor-intensive as well as the formation of considerable

quantities of dust, so let’s consider more ordinary manners.

The old finish is removed from the walls, and also the surface, if needed, is leveled to get rid of the requirement to paste

plaster onto a thick layer of glue.

Combining such cladding with other types of interior finishes can be both orderly and done with no clear consequences,

chaotically, together with fake of indications of aging.

With the help of decorative gypsum tiles it is possible to imitate a large number of textures.

A large number of textures may be imitated with the support of decorative gypsum tiles.

The wall where it is to be set up must have the following characteristics:

* Hardness and durability of the outside;

* The lack of uneven places and sharp sections;

* no deformations.

Decorative tiles at the interior of the kitchen

Walls are created from a variety of substances, so let us break down the principles of installation.

When dealing with concrete, there will be no big problems. It is only essential to take into account the porosity of the material.

Concrete, which has practically no pronounced pores, should be treated with a good primer.

Mounting gypsum tiles on concrete

Before starting work on the setup of gypsum tiles on the walls, then it is well worth assessing the strength of their surface.

When the plaster doesn’t fall off the walls and in exactly the exact same time holds nicely, it is possible to simply paint it

using primer.

Mount the tiles onto the painted concrete shouldn’t. The surface should be scratched, making sure to misfire, then it ought to be

grouted and coated with a layer of plaster.

カテゴリー: laying パーマリンク